Skip to content

Directional drilling & boring · Serving Dallas and all of Texas

(855) 804-1434

D Directional-Drilling.net Dallas

Serving Dallas and all of Texas

Directional drilling contractors in Dallas, TX

Horizontal directional drilling, auger boring and pipe boring in Dallas: conduit, fiber, water, sewer and gas lines put under roads, driveways and landscaping without an open trench.

Call (855) 804-1434Estimates are free. Call now. Request a free estimate

Most of the underground lines being installed in Dallas today never see an open trench. Directional drilling runs a steered pilot bore between two pits, reams it to size and pulls the pipe or conduit back through in one pass. For a crossing under a Texas highway, a railroad or a river, it is usually the only method the permit will allow.

Open territory · Dallas, TX

Drilling contractors covering Dallas

No single contractor is listed for Texas yet. Call the national line or use the form and the request is routed to a directional drilling contractor working the Dallas area. Estimates are free.

(855) 804-1434

What is in the ground in Dallas

Expansive clay across Dallas–Fort Worth and Houston with limestone and caliche in Austin and San Antonio; West Texas is caliche and sand over rock, and the coast is soft clay with a shallow water table.

Subdivision and data-center utilities, fiber to the home, water and wastewater expansion in the fast-growing suburbs and TxDOT highway crossings statewide. Locate requests in Texas go through Texas811; crossings of state routes are permitted by TxDOT.

How a bore in Dallas is done

On a typical Dallas job the crew sets up an entry pit on one side of the obstruction and an exit pit on the other, calls in the Texas811 ticket, and drills a pilot hole that is tracked by a walkover locator above ground. Drilling fluid, usually a bentonite and water mix, carries cuttings out, lubricates the pipe and holds the hole open in sand or soft soil. The hole is reamed to size and the product is pulled in.

Hiring a drilling contractor in Dallas

A good Dallas drilling contractor is easy to pick out from a quote. The length, pipe size and material are stated, the crossing permits are listed, locates and traffic control are either included or called out, and the mobilization fee, if there is one, is written down. A quote with only a price and a date leaves every one of those as a surprise.

Estimates are free. Call now: (855) 804-1434.

Drilling and boring services in Dallas

Each page explains one method or utility type: what gets installed, how deep, what the permit requires and what moves the price.

Directional Drilling

Horizontal directional drilling (HDD) for new underground utilities: steered bores under roads, driveways, parking lots, creeks and landscaping with no open trench.

Directional Drilling explained →

Horizontal Boring

Horizontal boring for conduit, casing and carrier pipe where digging across a surface is not an option.

Horizontal Boring explained →

Auger Boring

Steel-cased auger bores for road, rail and railroad crossings that need a straight, on-grade casing.

Auger Boring explained →

Pipe Boring

Boring and pulling in HDPE or steel product pipe from a few inches up to large-diameter casings.

Pipe Boring explained →

Fiber Optic Drilling

Directional drilling for fiber and communications duct: long bores, multiple ducts in one pull, tight easements.

Fiber Optic Drilling explained →

Electrical Conduit Drilling

Bores for primary and secondary power conduit, lighting circuits and site electrical feeds.

Electrical Conduit Drilling explained →

Utility Drilling

Multi-utility installs for developers and utilities: power, gas, water, sewer and telecom on one site plan.

Utility Drilling explained →

Sewer Line Drilling

Directional drilling and boring for new gravity-adjusted force mains, laterals and sewer crossings.

Sewer Line Drilling explained →

Water Main Drilling

HDD installation of new water mains and service lines, including creek and road crossings.

Water Main Drilling explained →

Gas Line Drilling

Bores for new natural gas mains and services, coordinated with the utility and its operator-qualification rules.

Gas Line Drilling explained →

Questions we hear in Dallas

Can directional drilling install a sewer line in Dallas?+

Yes, with planning. Gravity sewer needs a consistent slope that HDD can hold on shorter bores with careful steering; force mains and pressure sewer have no slope requirement and are routine. Many Dallas sewer crossings are done by auger boring with a steel casing when exact grade is critical.

Do I need a permit to bore under a street in Dallas?+

Yes. Work in a public right-of-way needs a permit from the city or county, and a crossing of a state route needs a Texas DOT encroachment or utility permit. Railroad crossings have their own agreement. Your contractor should file these; make sure the quote says who does.

How long does a bore take in Dallas?+

A single residential or small commercial crossing of a few hundred feet is usually a one- or two-day job including setup, pilot bore, reaming and pullback. Longer or larger bores, rock, and permit-driven traffic control stretch that out. Restoration is limited to the two pits.

How do I get a directional drilling estimate in Dallas?+

Call (855) 804-1434 or use the form on this page and the request is routed to a drilling contractor covering Dallas; estimates are free. Have the length of the run, what is going in the ground and what it crosses ready, and a site walk will usually confirm the price.

More Texas cities

Every listed city in Texas has its own page; the Texas page covers the state's ground, permits and contractor.

Free Estimates

Tell us what needs to go in the ground in Dallas.

Length of the run, what is being installed (conduit, duct, water, sewer, gas), what it has to cross, and where the plans stand. A crew that bores for a living can usually price it from that and a site walk.

Estimates are free. Call now. (855) 804-1434
  • ✓ Road, driveway, creek and rail crossings without cutting the surface
  • ✓ Conduit, duct, casing and product pipe from 2" to large diameter
  • ✓ Locates, bore plans and utility coordination handled
  • ✓ Crews travel; a mobilization fee is quoted up front on far jobs

Request a free estimate

We match you with a drilling contractor covering Dallas.

No obligation. Your details go only to the drilling contractor handling your area.