Serving Murfreesboro and all of Tennessee
Directional drilling contractors in Murfreesboro, TN
Horizontal directional drilling, auger boring and pipe boring in Murfreesboro: conduit, fiber, water, sewer and gas lines put under roads, driveways and landscaping without an open trench.
Most of the underground lines being installed in Murfreesboro today never see an open trench. Directional drilling runs a steered pilot bore between two pits, reams it to size and pulls the pipe or conduit back through in one pass. For a crossing under a Tennessee highway, a railroad or a river, it is usually the only method the permit will allow.
In Tennessee the listed contractor is Davis Underground Solutions, Inc., based in Powder Springs, Georgia, which drills across the Southeast and quotes any mobilization up front. See Davis Underground Solutions's Tennessee drilling page for the crew, the equipment and recent projects, or call (855) 520-2670; estimates are free.
Serving Murfreesboro and all of Tennessee
Davis Underground Solutions, Inc.
Directional drilling, auger boring and utility installation; locates, bore plan and permits handled. It's boring. But we dig it.
What is in the ground in Murfreesboro
Limestone and karst across Middle Tennessee with shallow rock around Nashville and Murfreesboro; West Tennessee is loess and alluvial clay with high groundwater near Memphis, and East Tennessee is shale, sandstone and dolomite in ridge-and-valley terrain.
Nashville-area growth, fiber to the home, water-system renewal in the smaller utility districts and crossings of the Cumberland, Tennessee and their tributaries. Locate requests in Tennessee go through Tennessee 811; crossings of state routes are permitted by TDOT.
How a bore in Murfreesboro is done
On a typical Murfreesboro job the crew sets up an entry pit on one side of the obstruction and an exit pit on the other, calls in the Tennessee 811 ticket, and drills a pilot hole that is tracked by a walkover locator above ground. Drilling fluid, usually a bentonite and water mix, carries cuttings out, lubricates the pipe and holds the hole open in sand or soft soil. The hole is reamed to size and the product is pulled in.
Hiring a drilling contractor in Murfreesboro
A good Murfreesboro drilling contractor is easy to pick out from a quote. The length, pipe size and material are stated, the crossing permits are listed, locates and traffic control are either included or called out, and the mobilization fee, if there is one, is written down. A quote with only a price and a date leaves every one of those as a surprise.
Estimates are free. Call now: (855) 520-2670.
Drilling and boring services in Murfreesboro
Each page explains one method or utility type: what gets installed, how deep, what the permit requires and what moves the price.
Directional Drilling
Horizontal directional drilling (HDD) for new underground utilities: steered bores under roads, driveways, parking lots, creeks and landscaping with no open trench.
Directional Drilling explained →
Horizontal Boring
Horizontal boring for conduit, casing and carrier pipe where digging across a surface is not an option.
Horizontal Boring explained →
Auger Boring
Steel-cased auger bores for road, rail and railroad crossings that need a straight, on-grade casing.
Auger Boring explained →
Pipe Boring
Boring and pulling in HDPE or steel product pipe from a few inches up to large-diameter casings.
Pipe Boring explained →
Fiber Optic Drilling
Directional drilling for fiber and communications duct: long bores, multiple ducts in one pull, tight easements.
Fiber Optic Drilling explained →
Electrical Conduit Drilling
Bores for primary and secondary power conduit, lighting circuits and site electrical feeds.
Electrical Conduit Drilling explained →
Utility Drilling
Multi-utility installs for developers and utilities: power, gas, water, sewer and telecom on one site plan.
Utility Drilling explained →
Sewer Line Drilling
Directional drilling and boring for new gravity-adjusted force mains, laterals and sewer crossings.
Sewer Line Drilling explained →
Water Main Drilling
HDD installation of new water mains and service lines, including creek and road crossings.
Water Main Drilling explained →
Gas Line Drilling
Bores for new natural gas mains and services, coordinated with the utility and its operator-qualification rules.
Gas Line Drilling explained →
Questions we hear in Murfreesboro
What size pipe can be installed by directional drilling in Murfreesboro?+
Residential and small commercial bores commonly place 1-inch to 6-inch conduit, water or gas lines. Mid-size rigs handle 8-inch to 16-inch product, and large rigs install 24-inch and larger steel or HDPE under rivers and highways. The soil and the length of the run matter as much as the rig's rated pullback.
Is directional drilling cheaper than digging a trench in Murfreesboro?+
For a crossing under pavement, a driveway, mature landscaping or a creek, boring is almost always cheaper once you count the cutting, backfill, repaving and restoration that a trench requires. In an open field with nothing to cross, a trench can be less. A good contractor will tell you which applies to your job.
How deep does a directional bore go under a road in Murfreesboro?+
Most road crossings in Tennessee are bored 4 to 10 feet below the pavement, deeper under state highways and railroads where the permit sets a minimum cover. The depth also depends on the pipe diameter and the bend radius the product can tolerate; a longer bore lets the crew ease down to depth and back up more gradually.
How do I get a directional drilling estimate in Murfreesboro?+
Call Davis Underground Solutions, Inc. at (855) 520-2670; estimates are free, and the crew that answers is the one that does the work. Have the length of the run, what is going in the ground and what it crosses ready, and a site walk will usually confirm the price.
More Tennessee cities
Every listed city in Tennessee has its own page; the Tennessee page covers the state's ground, permits and contractor.