Serving Yakima and all of Washington
Directional drilling contractors in Yakima, WA
Horizontal directional drilling, auger boring and pipe boring in Yakima: conduit, fiber, water, sewer and gas lines put under roads, driveways and landscaping without an open trench.
Property owners, builders and utilities in Yakima call a boring contractor for the same reason: something has to go in the ground where the surface cannot be disturbed. Directional drilling and auger boring do that, placing conduit, duct, casing or pipe underneath roads, slabs, creeks and landscaping from entry and exit pits that are a few feet square.
Open territory · Yakima, WA
Drilling contractors covering Yakima
No single contractor is listed for Washington yet. Call the national line or use the form and the request is routed to a directional drilling contractor working the Yakima area. Estimates are free.
(855) 804-1434What is in the ground in Yakima
Glacial till, outwash and clay around Puget Sound with boulders and a high winter water table; eastern Washington is basalt and loess, and the Columbia valley is sand and gravel.
Fiber and conduit in the Seattle suburbs, water-system seismic upgrades, irrigation and utility crossings in the Yakima and Tri-Cities areas and public-utility-district broadband builds. Locate requests in Washington go through Washington 811; crossings of state routes are permitted by WSDOT.
How a bore in Yakima is done
The sequence in Yakima is locate, plan, pilot, ream, pull. The Washington 811 locate marks the public utilities, the bore plan sets depth and clearances, the pilot bore is steered along that plan and tracked from above, the hole is enlarged to about one and a half times the pipe diameter, and the pipe is pulled back from the exit pit to the entry pit. Fluid returns are contained at both pits and hauled off or recycled.
Hiring a drilling contractor in Yakima
The questions that matter when hiring in Yakima: Has the crew bored in this soil before? Who files the Washington 811 ticket and the Washington permits? What diameter and length can the rig on this job handle? What is the plan for fluid returns, and for a bore that drifts off line? Is the price per foot or for the finished crossing? A contractor who bores for a living answers all of them without hesitation.
Estimates are free. Call now: (855) 804-1434.
Drilling and boring services in Yakima
Each page explains one method or utility type: what gets installed, how deep, what the permit requires and what moves the price.
Directional Drilling
Horizontal directional drilling (HDD) for new underground utilities: steered bores under roads, driveways, parking lots, creeks and landscaping with no open trench.
Directional Drilling explained →
Horizontal Boring
Horizontal boring for conduit, casing and carrier pipe where digging across a surface is not an option.
Horizontal Boring explained →
Auger Boring
Steel-cased auger bores for road, rail and railroad crossings that need a straight, on-grade casing.
Auger Boring explained →
Pipe Boring
Boring and pulling in HDPE or steel product pipe from a few inches up to large-diameter casings.
Pipe Boring explained →
Fiber Optic Drilling
Directional drilling for fiber and communications duct: long bores, multiple ducts in one pull, tight easements.
Fiber Optic Drilling explained →
Electrical Conduit Drilling
Bores for primary and secondary power conduit, lighting circuits and site electrical feeds.
Electrical Conduit Drilling explained →
Utility Drilling
Multi-utility installs for developers and utilities: power, gas, water, sewer and telecom on one site plan.
Utility Drilling explained →
Sewer Line Drilling
Directional drilling and boring for new gravity-adjusted force mains, laterals and sewer crossings.
Sewer Line Drilling explained →
Water Main Drilling
HDD installation of new water mains and service lines, including creek and road crossings.
Water Main Drilling explained →
Gas Line Drilling
Bores for new natural gas mains and services, coordinated with the utility and its operator-qualification rules.
Gas Line Drilling explained →
Questions we hear in Yakima
How deep does a directional bore go under a road in Yakima?+
Most road crossings in Washington are bored 4 to 10 feet below the pavement, deeper under state highways and railroads where the permit sets a minimum cover. The depth also depends on the pipe diameter and the bend radius the product can tolerate; a longer bore lets the crew ease down to depth and back up more gradually.
What size pipe can be installed by directional drilling in Yakima?+
Residential and small commercial bores commonly place 1-inch to 6-inch conduit, water or gas lines. Mid-size rigs handle 8-inch to 16-inch product, and large rigs install 24-inch and larger steel or HDPE under rivers and highways. The soil and the length of the run matter as much as the rig's rated pullback.
Is directional drilling cheaper than digging a trench in Yakima?+
For a crossing under pavement, a driveway, mature landscaping or a creek, boring is almost always cheaper once you count the cutting, backfill, repaving and restoration that a trench requires. In an open field with nothing to cross, a trench can be less. A good contractor will tell you which applies to your job.
How do I get a directional drilling estimate in Yakima?+
Call (855) 804-1434 or use the form on this page and the request is routed to a drilling contractor covering Yakima; estimates are free. Have the length of the run, what is going in the ground and what it crosses ready, and a site walk will usually confirm the price.
More Washington cities
Every listed city in Washington has its own page; the Washington page covers the state's ground, permits and contractor.